Call

 

Everyone seems to have his or her own conception on the subject of A Step-by-Step Guide to Installing a Bathtub.

Setting up a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably challenging project. If the old tub is conveniently easily accessible, the job can move easily; if you need to open up a wall to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will need an assistant to leave the old tub and also set in the brand-new one. Make certain you have qualified on your own for the job and fit attempting it. As opposed to working with a professional to take over a halfway-completed task, it is far better to consider using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will assist you set up a new bathtub in your restroom if you have already bought a new bathtub and don't require to alter the setup of your previous water system pipes.
Your tools and material checklist ought to consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Installment

First of all, the supporting frame supplied with the bathroom ought to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to stop stress on the tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now be ready to be suited its last setting.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be rather bothersome as a result of the limited accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Installing the Bath tub

Making use of the two wooden boards under its feet, place the bathtub in the required position. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bath tub until the level reviews level.
To set up taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water system and also check all joints and also new pipework for leaks as well as tighten them if essential. Fill up the tub as well as additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the bathtub should wait up until the bathtub has been utilized a minimum of once as this will resolve it right into its final placement.

 

 

Fitting New Taps

If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the faucet in position with the manufacturer provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former type must be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bathtub

In the area where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes as well as cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealer can fracture relatively early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We hope you enjoyed our post about Tools You Need to Install a New Bathtub . Thank you so much for taking a few minutes to read our article. Sharing is good. One never knows, you could be helping someone out. Thank you for your time. Visit again soon.

Peace of mind? Dial!